A faucet spread refers to the width between handles. Single Hole. Providing more precise volume and temperature control, single-hole faucets make the most of a small sink space. This type of faucet is also much easier to install.
Thereof, what does faucet spread mean?
A widespread faucet is generally for larger sinks because it allows for more room between the faucet handles and spout than a centerset faucet. The ‘Spread’ is the distance between the faucet mounting holes. Usually centersets are single or four inch spacing between holes, while a widespread is wider.
Furthermore, what does a 4 inch centerset faucet mean? 4″ Centerset Faucets, are intended for sinks and countertops with 3 predrilled holes that are 4″ apart. Centerset faucets sit on a deckplate which connects the two handle bodies with the spout body.
Considering this, how do you measure faucet spread?
Measure the distance between the handles. Hold the the tape measure above the faucet if it’s in the way. If the distance is six inches or more you need a “widespread” or “eight inch spread” faucet.
Are faucets hard to replace?
Replacing a leaky or outdated faucet isn’t as difficult as you might think. You can tackle the project with a basin wrench and a few other common tools. It should usually take no more than about an hour. The same steps apply if you’re installing a new faucet onto a new sink.
17 Related Question Answers Found
How do I choose a sink faucet?
Tips on Choosing a Faucet Looks aren’t everything. Most people choose a faucet based on looks alone. Spend enough but not too much. Watch the spout height and reach. Choose ceramic valves. Some finishes are tougher than others. Count the holes in your sink. A single handle is more convenient. Pull-down sprayers are better.
What are the different types of faucets?
The most common faucet types are: Ball Faucet. The first type of washerless faucet, ball faucets are commonly used in kitchens. Cartridge Faucet (Two Handle) Cartridge faucets utilize a movable stem cartridge which moves up and down to control the flow of water. Disc Faucet. Compression Washer Faucet.
What is the difference between widespread and centerset faucets?
In many cases, but not all, centerset faucets combine the handles and spout together on a base unit. This configuration works well in small bathrooms with small sinks and limited space. A widespread faucet has hot and cold water handles that are independent of the spout and at least 6″ apart.
Will any faucet fit my sink?
Not all faucet types work with every sink, so it’s important to make sure the faucet you choose will fit your sink or basin. Standard faucet drillings are centerset, single-hole or widespread.
How do I know what type of faucet I have?
Identifying Your Faucet Model The model number is printed on a tag that is attached to the cold water supply line of the faucet. The supply line is located below the sink, countertop, bath rim, or behind the bowl of a bidet. The model number, or part number, is typically preceded by “P/N.” In the image above, the model number is 6227-V3-AA.
What does an 8 inch center faucet mean?
A 4″ measurement means you should look for a 4″ Centerset faucet or 4″ Minispread faucet. An 8″ measurement means you should look for an 8″ Widespread faucet. 4″ Centerset faucets are compact and join the three hole openings above the sink or countertop.
What is a faucet center?
Find Your Faucet Center This refers to the distance, in inches, between the pre-drilled faucet holes in the sink or vanity, from the very center of the left hole to the very center of the right hole. These center points should correspond to the center connections of the faucets to be installed there.
Can you replace a 2 handle faucet with a 1 handle faucet?
A single handled faucet has a faceplate that simply stretches across to cover the other two holes that aren’t in use. So, you can replace a single-handled faucet with a double-handled faucet or go the other way around, but can you do it on your own?
What is spout length?
Spout reach is measured from the center of the spout base horizontally out to the water stream. Spout height is measured from the sink/countertop surface vertically up to the highest point. Refer to the specification sheet for your faucet for specific measurements.
How do I choose a bathroom faucet?
Faucet Types Single-hole faucets combine the spout and mixing handles—often a single lever—into one unit that requires only one drilled sink hole. Center-set faucets fit standard three-hole sinks (with outer holes drilled 4 inches apart). Widespread mounts have three separate pieces: Two handles and the spout.
What are the different types of bathroom faucets?
What are the Different Types of Bathroom Faucets? Bridge. If you’re looking to combine old-fashioned style with today’s technology, bridge faucets might be for you! Centre-set. Bathroom faucets that are centre-set work with basins with three holes. Single-handle. Spread-fit. Deck mount. Wall-mount. Vessel.
How much space do you need behind a bathroom sink faucet?
Undermount and Faucet Sizing The undermount sink size includes one or two bowls, which range in size from 8 to 20 inches from side to side and 18 inches from the front to the back of the sink. That leaves an inch of space in front of the sink and 3 inches behind the sink for the faucet.
What is the difference between a faucet for a sink and a faucet for a tub?
Look for an all-brass body, as opposed to brass- or chrome-plated. And keep in mind that the tub faucet has a larger flow rate than other household faucets, which means you can’t use a kitchen faucet or your tub. Bathtub faucets should have a 3/4-inch supply line, as opposed to 1/2-inch for the rest of the house.
What is an 8 inch center faucet?
Most of the 8-inch or widespread faucets have three pieces, the tap and the hot and cold handles, which means some 8-inch faucets can fit holes not exactly 8 inches apart. If the span is 4 inches, a 4-inch faucet is what you need.
What does Centerset mean in a bathroom faucet?
?Centerset (4-inch Faucet Center) This style features a deckplate that contains the handles and spout in one plate. This type of faucet can be used on sinks and countertops with one to three holes. Centerset faucets require holes with 4-inch centers.
Are faucets standard size?
Standard size sink openings and faucet dimensions are used throughout the U.S. plumbing industry. Generally, the standard distance between hot and cold inlets or the mounting hardware for both single and two-handle kitchen model faucets is 8″ inches.
What is a 4 hole faucet?
4-HOLE SINK. A 4-hole sink is the most common kitchen sink. A 4-hole-sink faucet is like a 3-hole faucet (see above), with the addition of a soap dispenser or sprayer. 2-HOLE SINK. A 2-hole sink usually has one hole for a single-hole faucet and a second hole for an accessory, such as a soap dispenser or sprayer.