Fill: A switch opens a solenoid water valve and lets in just enough water to fill the ice mold. Freezing cycle: The icemaker has a built-in thermostat which monitors the temperature level of the water in the molds. After the cubes are ejected, the arm drops down again (or pushes out) to sense the ice.
Subsequently, one may also ask, how does a GE refrigerator ice maker work?
The icemaker mold thermostat monitors the temperature of the ice mold (ice tray). Once the mold reaches the proper temperature, the icemaker ejects the ice cubes and refills the ice mold with water.
Furthermore, how do I reset my GE ice maker? How to Reset the Ice Maker on a GE Side by Side Refrigerator
- Locate the shut-off switch on the front of the GE refrigerator ice maker and turn the switch off, leaving it off for at least 30 seconds.
- Turn the switch back on and locate the feeler arm on the ice maker.
- Push the feeler arm up three times quickly to reset the ice maker.
Considering this, why is my GE ice maker not making ice?
If your icemaker is not producing any ice: The icemaker must reach 16 degrees F before a cycle will begin. If the temperature in the freezer is too warm, ice cubes will take longer to form or may not form at all. Try adjusting the freezer temperature.
Why isn’t my icemaker working?
If your ice maker isn’t producing ice at all or is producing crescents or cubes that are smaller than usual, it’s typically indicative of a clog somewhere along the supply line. Cause: A common cause for a clog is frozen water in the line. Fix: To repair a frozen line, slide the refrigerator and unplug it.
9 Related Question Answers Found
How long does it take for an ice maker to make ice?
6 to 12 hours
How do I reset my ice maker?
Unplug the refrigerator for 30 seconds; then plug it back in. Within 15 seconds of restoring power, press the feeler arm three times in succession. This should force the ice maker to run water into the reservoir and begin the cycle of ice production.
How do you turn off GE side by side ice maker?
To turn it off, set the power switch to O for off. If there is an on/off slide switch, you turn it off by sliding the switch, so the paddle is under the icemaker. Models without a switch: If no switch is present, gently lift the metal feeler arm on the side of the ice maker to the up position to turn the unit off.
How do I test my GE ice maker?
Electronic Icemaker Power ON Diagnostics Test Mode Turn on the motor until it reaches home position. Turn on the water valve for 1/2 second. Turn on the heater for 1/2 second. Verify that the feeler arm was in the ‘in’ and then the ‘out’ position.
How do I know if my ice maker is bad?
If the ice maker makes cubes and kicks them into the bucket – the water inlet valve is bad. If there are no new cubes in the bucket – the ice maker is bad.
Does refrigerator water filter affect ice maker?
If the filter is clogged, water can’t get through to create ice. For standard refrigerator maintenance, we recommend cleaning the ice maker every three months and changing the water filter every six months.
How do I unclog my ice maker water line?
Shut off the water valve that feeds that water-dispenser and ice-maker lines. Remove the ice bin and dump the ice out in the sink. Pour 3 to 4 cups of white distilled vinegar into the ice-maker and dispenser lines with a small funnel and allow it to soak for five to 10 minutes to break down the lime.
Is there a reset button on a GE refrigerator?
Unfortunately, there is no easy reset button so the computer must be reset manually. To reset your refrigerator: Unplug the refrigerator from the power source or turn off power at the circuit breaker.
How long does it take a GE ice maker to make ice?
If the icemaker was installed but the water line was not added until later, once the water and icemaker is turned on the icemaker will cycle within a few minutes and fill and process its first cubes in about 1 1/2 hrs. The icemaker is dependant upon the temperature in the freezer.