Open the drain pump filter cover at the bottom of the washer front panel. Remove the screws that secure the plastic pump housing to the frame of the washer. Remove the plastic pump housing. Use a Phillips screwdriver to remove the mounting screw from the bottom of the front panel.
Similarly, it is asked, where is the pump on a Kenmore front load washer?
The drain pump is located in the lower front corner of most Kenmore front-loading machines, and the most difficult part of the job may be getting to it. If the machine doesn’t have an access panel, as some do, you’ll have to take the entire front panel off.
Also, how do I know if my washing machine pump is bad? If the motor and pump is running but no water is draining out then most likely the 3363394 pump is bad. One thing you can try first is to lower the drain hose over a shallow pan and see if the water in the tub will drain by gravity. If not then there may be a sock or other obstruction blocking the pump.
Also Know, where is the drain pump on a LG front load washer?
Locate the pump at the front of the machine on the bottom left. Remove the three screws that encircle the front of the pump. Note where each drain hose connects to the pump so you can reconnect it properly later. Pinch the tabs on the clips that secure the hoses to the pump while pulling the hoses off.
How do you fix a washing machine drain pump?
How to Repair a Washing Machine
- Step 1: Check the drain hoses to make sure they’re draining properly.
- Step 2: To access the pump, first bail and sponge out any water in the machine’s tub.
- Step 3: Locate the pump.
- Step 4: To remove the pump, loosen the bolt that holds the drive belt taut and move the washer motor on the bracket to loosen the belt.
7 Related Question Answers Found
Where is the drain pump on a front load washer?
Open the drain pump filter cover at the bottom of the washer front panel. Remove the screw that secures the plastic pump housing to the frame of the washer. Remove the plastic pump housing. Remove the mounting screw from bottom of the front panel.
How do you test a washing machine pump?
How to Use an Ohmmeter to Test a Washing Machine Pump Check the washing machine power cord to ensure it is unplugged from the electrical outlet. Turn on the ohmmeter and touch the probes together. Adjust the scale dial to zero. Find the two wires connecting to the side of the pump. Touch a probe to each of the terminals on the pump.
Why does my washing machine not drain completely?
If the washer won’t drain there might be a clogged pump or hose. It’s common for small socks or other small clothing items to get into the water drain system and clog the hose leading to the pump or the pump itself. Cleaned the filter and the machine still will not drain. So that must mean the hose or pump is clogged.
How do you replace a drain pump on a Kenmore he2 washer?
Replace a Drain Pump in a Kenmore / Whirlpool Washer Step 1: Items Needed. You will need a few item to change the pump. Step 2: Unplug the Machine. Just a reminder to make sure power is off. Step 3: Remove Lower Front Panel. Step 4: Drain Washer. Step 5: Remove Old Pump and Motor. Step 6: Water in Motor Housing. Step 7: Connector Difference. Step 8: Wiring the Motor.
Where is the drain pump located on a washing machine?
The purpose of the drain pump is to pump the water from the wash, through the drain hose, to then be drained away. The drain pump is located at the bottom of your washing machine, but can be easily accessed in order to replace it if need be.
How much is a pump for a washer?
The most important part is a new washer pump. It can cost as little as $10 or as much as $75 or more. However, most homeowners pay between $25-$40 for a new pump.
How do you drain a washing machine?
Start by unplugging the machine and emptying the water. Bail the water out of the tub, or you can drain the tub using gravity by placing the washer drain hose on the floor near the drain or in a bucket. Clamp the hose to prevent any remaining water from running out.