How do you reset a Whirlpool Cabrio washing machine?

How To Reset Whirlpool Cabrio Washer:

  1. Turn the washer off.
  2. Set the mode selector dial to NORMAL.
  3. Turn the dial counter clockwise ONE click (LEFT), clockwise THREE clicks (RIGHT), counter clockwise ONE click (LEFT) then clockwise ONE click (RIGHT).
  4. Now press the start button.

Correspondingly, why is my Whirlpool Cabrio Washer not working?

This is usually caused by a clog in the drain line or something obstructing the pump. Clean out any lint or obstruction (coin, small button) that is clogging the pump filter. Turn off the water connections. If these steps don’t solve the problem, the washer’s water pump may need to be replaced.

Beside above, how do you reset a washing machine? How to reset the washing machine:

  1. Press POWER to turn the washer off.
  2. Unplug the washer from the power outlet or turn the circuit breaker to the unit off.
  3. With the power disabled, press and hold the START/PAUSE button for 5 seconds.
  4. Plug the washer back in, or turn the circuit breaker back on.

One may also ask, how do you run a diagnostic on a Whirlpool Cabrio washer?

HOW TO ACTIVATE DIAGNOSTIC MODE ON A WHIRLPOOL CABRIO WASHER

  1. Press and hold that button for 3 seconds, then release it for 3 seconds.
  2. Press and hold it again for 3 more seconds, then release it for 3 seconds.
  3. Press and hold for 3 seconds.

How do you reset the error code on a Whirlpool Cabrio washer?

How to Reset a Whirlpool Cabrio

  1. Touch any key on the display pad to clear the error code, if applicable, or press “Pause/Cancel.”
  2. Choose a new cycle and press “Start” to begin.
  3. Turn off and disconnect the Cabrio if the error or problem persists.
  4. Wait several minutes before restoring power.
  5. Contact Whirlpool for assistance if the unit will not reset.

6 Related Question Answers Found

How do I reset my Whirlpool top load washer?

Unplug the washer for 1 minute from the electrical outlet. Plug the washer back in and lift and lower the lid 6 times within a 12 second period. You have 30 seconds to start lifting and lowering the lid. The motor has now been reset and is ready for you to start a cycle.

What does the Code F mean on a Whirlpool washer?

The “F” error code indicates the washing machine system or “Fault”. Ehe “E” error is indicating the part in your washer that causing the issue or “Error”. As a general rule, these “F” error codes mean the following… – Whirlpool Duet Washing Machine F5 error code indicates door lock and door switch issues.

How do you calibrate a Whirlpool Cabrio washing machine?

CABRIO WASHER CALIBRATION CYCLE Pick three buttons ( Do not use Power button) and within 8 seconds. Make sure the washer is in (Stand By Mode) which means the machine is plugged in and all the indicator lights are off. Press and Release the 1st selected button, Press and Release the 2nd selected button,

How do you troubleshoot a washing machine?

Many times the solution is an easy fix or an inexpensive part. Drain Hose. When a washer leaks only during the spin cycle the likely cause is the drain hose. Fill Hose. The fill hoses could also be the culprit. Water-Inlet Valve. Too Much Detergent. Door Seal (front-load) Drain Pump. Drains and Hoses. Tub.

How do you bypass a Whirlpool Cabrio lid lock?

How to Bypass a Washing Machine Lid Lock Turn off the washer and unplug the appliance. Locate the retaining tabs and/or screws that hold the top horizontal panel down. Look for the lid lock switch on the underside of the top panel and where it fits into the appliance. Put the lid back down and plug the washing machine back into the electrical outlet.

What is wrong when a washer doesn’t spin?

If your washer fills with water but doesn’t agitate, the problem is likely to be a faulty lid switch, a broken belt, or a problem with the motor. 1 Check the washing machine’s spin cycle. If this works, the motor is operating and the belt is not broken. If the spin cycle doesn’t work, the belt may be loose or broken.

Leave a Comment