Instructions for How to Attach Fascia Board to Roof Trusses
Use the carpenter’s square and pencil to put a straight line at the mark. Cut the board with a miter saw. Position the board against the trusses and nail it in place. Put at least 2 nails at both ends of the fascia board into the joists.
Similarly, you may ask, how do you attach fascia boards?
Nail the first fascia board in place with 2-inch finish nails and a hammer. Drive at least two nails through the fascia into the end of each joist. Butt the next fascia piece to the open end of the first so that it it aligned with the center of the joist where the first board ends.
Secondly, is sub fascia necessary? Floor Plans. Sub-fascias are not required by code. The fascia can be nailed directly to the truss tails, but while the sub-fascia is typically a t.
People also ask, how much do you overlap fascia?
Overlap Each Section Each piece should overlap the previous section of aluminum fascia by 1 to 2 inches, but the overlap should be a smooth transition that doesn’t cause bumps or raised areas. Be sure that the cuts are straight, and follow the correct angles.
How do you attach fascia to rafters?
Instructions for How to Attach Fascia Board to Roof Trusses Use the carpenter’s square and pencil to put a straight line at the mark. Cut the board with a miter saw. Position the board against the trusses and nail it in place. Put at least 2 nails at both ends of the fascia board into the joists.
17 Related Question Answers Found
How do you cut angles for fascia?
Set the angle of a miter saw to 45 degrees so you can make clean cuts through the board. Put on your safety glasses, and position the fascia board so the corner on one end lines up with the saw blade. Turn the saw on and pull it down to cut the angle. Cut the ends of any other boards that will be on a corner.
What size should fascia board be?
You construct fascia boards out of 1-inch lumber. The width depends on the width of the rafters, but since builders generally use two-by-six or two-by-eight lumber for roof construction, the most common dimensions for fascia boards are one-by-six and one-by-eight inches.
How do you seal fascia boards?
Start at the end of a fascia board and caulk the corner edge where two boards meet. Smooth the caulk bead with your finger and begin caulking the joint between the fascia board and the soffit (also known as the eave). Slowly move down the joint to apply a steady bead of caulk into the gap.
What nails do you use for fascia?
Hardie Trim It calls for 2-inch, 16-gauge, corrosion-resistant finish nails only when you are attaching fascia to double sub-fascia. Nails should not be closer than 1 1/4 inches from the edges and no nearer than one inch from the ends. With pneumatic nailing, Hardie Trim recommends driving the finish nails flush.
How do you replace fascia with drip edge?
Removing Drip Edge Eave Strips: Gently lift up the shingles along the lower edge of the roof, and find the nails attaching the eave strip to the roof decking. Use a flat pry bar and hammer to remove the nails holding the eave strip to the roof decking. Slip the eave strip out from under the shingles.
How much does it cost to replace fascia and soffit?
Replacing your soffit generally costs about $20 to $30 a linear foot installed, while replacing your fascia costs about $15 to $25 a linear foot installed. Prices for the project depend on a number of factors, including the materials used and the size of your house.
How do you install gutters without fascia?
A house without fascia needs to have gutters set up using roof straps. The roof straps are fitted to the hanger in the gutter and attached directly to the roof. If the roof is ancient, then it would be wise not to lift up the shingles in a bid to reach the strap under, because it could rupture or break the shingle.
What is a fascia on a house?
The fascia board is the one mounted at the point where the roof meets the outer walls of the house and is often called the ROOFLINE. However most people refer to it by the name of the main board that carries the gutter – the fascia or fascias.
How do you pronounce the word fascia?
noun, plural fas·ci·ae [fash-ee-ee] for 1, 3–5; fas·cias [fey-shuh z] for 2. a band or fillet, as for binding the hair. Also called fascia board. facia.
How do you bend aluminum fascia?
Step 1: Acquire a Brake Tool. A brake tool is a device that is used to bend aluminum and other metals. Step 2: Create Cuts in the Aluminum. Line the aluminum piece up with the combination square in a straight edge and measure in about an inch. Step 3: Bend the Aluminum. Step 4: Bend the Fascia to Match the Gutters.
How do you remove aluminum fascia?
Slide the end of the pry bar between the top of an aluminum soffit panel and the bottom of the fascia board. Pull down to release the nails from the bottom of the board. Ensure all nails are removed from the panel. Slide the panel toward the end of the eave to remove it from the J-channel installed on the house.
How do you remove aluminum soffit without removing fascia?
1 Answer. Assuming you have metal fascia as well, gently remove the nails securing a section of it where you need to work. Flex it out, then remove the hidden nails holding the soffit. Lower the soffit panels slightly by tilting them downward, and slide them past the fascia individually.
Can you paint aluminum fascia?
Aluminum soffits are nonporous. This makes them poorly suited for paint. Treat the soffit with a special acidic base coat, formulated for metallic surfaces. Once the soffits are primed, they will take a painted finish.
Can you bend vinyl fascia?
When the vinyl expands it will pucker around the nails. Coil stock is a roll of flat aluminum you bend with a metal bender as needed. You can buy pre bent aluminum fascia which is easy to work with and fast to install.
Can you nail vinyl fascia?
Do not nail vinyl fascia under any circumstances. When overlapping fascia panels, first cut a notch in the underlying panel.
What is the difference between soffit and fascia?
Typically a soffit is used in the area beneath the eaves on the exterior of a house to close the space beneath the eave. The soffit extends from the side of the structure to the edge of the eave. Fascia is used to create a barrier between the edge of the roof and the outside.
What is vinyl fascia?
Fascia board is the flat horizontal board along the edge of a roof. The fascia is nailed to the ends of the roof rafters, and is used to attach a gutter to the roof and soffit panels underneath the eaves. When installing new vinyl siding on your home, you can install vinyl trim on the fascia.