1 Factory Reset
- From the Home screen, press Menu.
- Select Settings.
- Go to Reset.
- Choose Reset All Settings then confirm your selection by pressing Yes.
- Choose the reset option that suits your needs:
- The ecobee thermostat will be reset to factory defaults.
Then, how do I reset my ecobee 4?
If it doesn’t work, restart your router by unplugging it, waiting a few minutes, then plugging back in. Once you have confirmed that the wi-fi is working for other devices, it’s time to try restarting your Ecobee. Turn it off, wait at least one minute, then turn it back on again. Allow your Ecobee to boot up as normal.
Secondly, how do I reset my ecobee without password? Visit https://www.ecobee.com/lost-password/ to reset your password. A password reset email will be sent to the email address linked to you registered thermostat via [email protected]ecobee.com.
Secondly, why is my ecobee not working?
Open the panel on your furnace to expose the control panel where your thermostat wires are connected. Most systems have a purple 3 or an orange 5 amp fuse on the board—check this fuse to ensure that it’s intact. A blown fuse will have to be replaced. Once a blown fuse is replaced, the ecobee should power back on.
Why is my ecobee rebooting?
If your ecobee thermostat is frequently rebooting, your HVAC system may be cutting power the thermostat. The most common causes of your HVAC system cutting power to your thermostat are: If your furnace overheats, this sensor will trip, causing the furnace to cut power to your thermostat.
19 Related Question Answers Found
How long does ecobee take to calibrate?
5 to 20 minutes
How do I reconnect my ecobee to WIFI?
To connect your Ecobee thermostat to your Wi-Fi network: From the Home screen, press Menu. Then select Settings. Go to Wi-Fi. Make sure Wi-Fi Radio is Enabled. Go to Network. Tap on Select Wi-Fi Network. Pick your Wi-Fi network from the list and enter your Wi-Fi password if required.
Why does my ecobee keep shutting off?
If your ecobee thermostat is frequently rebooting, your HVAC system may be cutting power the thermostat. The most common causes of your HVAC system cutting power to your thermostat are: If your furnace overheats, this sensor will trip, causing the furnace to cut power to your thermostat.
How do I unlock my Ecobee thermostat?
How to Lock Your Ecobee Thermostat with a PIN Code If you have kids in the house and are strict about the thermostat, you can lock down your Ecobee with a PIN code so that no one can adjust the temperature except those authorized to do so. Scroll down and tap on “Settings”. Select “Access Control”. Tap on “Enable Security Code”.
How do I calibrate my Ecobee thermostat?
To Configure Temperature Correction Press Menu on the main screen. Go to Settings. Then go to Installation Settings. Select Thresholds. Then select Temperature Correction. Adjust the temperature reading to fit your needs.
How do I unplug my ecobee?
To remove the ecobee backplate, carefully remove your thermostat from the backplate by putting your thumb and index finger on the backplate. Then, pull against the ecobee3 lite. Remove the screws from the backplate to remove it from the wall.
Where do I find my ecobee code?
Obtaining the Registration Code This code is obtained by doing the following on your ecobee thermostat’s screen: 1. Tap the three horizontal bars on the bottom left corner of the ecobee screen to open the Main Menu. After completing these steps, the code will then be displayed on the thermostat’s screen.
How do I update ecobee firmware?
0.339 or higher. The firmware version can be checked one of two ways: On the thermostat, select More > Settings > About > Version > ecobee Smart. From the web portal select Settings tab > open the About widget > click on the Version tab > Thermostat Software version.
Does ecobee work if WIFI goes out?
The ecobee will still operate as a thermostat to maintain it’s set temperatures and use the wireless sensors, if there’s any connected. They only difference, you won’t be able to monitor or control it remotely until it reconnects. You just cant access the wifi portion.
Does Ecobee thermostat have a battery?
The Ecobee comes with one wireless sensor, which is powered by a CR2032 coin-cell battery; the company says it should last about 4 years. When the battery runs low, you’ll receive an alert.
How do I turn on my ecobee air conditioner?
While on this system mode, the ecobee will display two set points—one for heating and one for cooling. The cooling set point is blue while the heating set point is orange. To enable this system mode, go to Main Menu > Settings > Installation Settings > Thresholds > Auto Heat/Cool and select Enable.
Does ecobee screen turn off?
Screen Brightness You can customize the brightness of your ecobee thermostat’s screen. You can also configure the screen to automatically sleep (i.e. turn off) whenever your ecobee thermostat enters the Sleep activity period.
What’s better nest or ecobee?
If you have a two-wire system, only the Nest will work. If you have more than two wires but no C-wire, the Ecobee is a better choice because it comes with a special power extender kit that essentially turns one of the wires into a C-wire for your thermostat. If you have a C-wire, either model should work just fine.
How do I remove ecobee schedule?
Fortunately, there is indeed a way: Head to the Ecobee site and sign into your account. Click Settings > Preferences > Hold Action, then choose Until the next scheduled activity. Now close the Settings window.
How do I reset my ecobee password?
Visit https://www.ecobee.com/lost-password/ to reset your password. A password reset email will be sent to the email address linked to you registered thermostat via [email protected]ecobee.com.
Why does my ecobee keep calibrating?
The “Calibrating: Heating and Cooling Disabled” message on your ecobee’s screen is displayed after the thermostat boots up. If you feel your thermostat has rebooted in error or that it is frequently rebooting, it may be rebooting due to an installation error or sudden power loss.
How accurate are ecobee sensors?
How accurate is the temperature sensor in the ecobee? The ecobee temperature sensor has a +/- 1.0F accuracy and is programmed to provide readings every 15 seconds. It will use the previous two values and average them into the current reading.
How do I install an Ecobee thermostat?
How to Install an ecobee3 Smart Thermostat 73 Step 1: Kill the Power to your HVAC. Step 2: Understand A Little About Thermostat Wiring. Step 3: Remove Your Old Thermostat. Step 4: Install the ecobee Power Extender Kit (PEK) Step 4-and-a-Half: Connect the Unused “C” Wire to your HVAC Control Board.
Why is my ecobee flashing green light?
My ecobee is flashing a green light! What do I do? This is Alexa letting you know that you have a notification. To check your notification and/or get rid of the flashing green light, just say “Alexa, what did I miss?” or “Alexa, delete all of my notifications” to your ecobee thermostat.