To install, simply slide the adjustable rod to fit inside your window casing and twist the rod to lock in place. To convert into a double curtain rod, insert a 7/16″ spring tension rod into the circular depressions toward the back of each bracket.
Beside this, how do you install blackout curtain rods?
How to Install Blackout Curtains
- Rod Placement. Choose where to place your curtain rod.
- Bracket Placement. Use a pencil and tape measure to mark where you will place the brackets.
- Attach Brackets.
- Hang Curtains.
- Prepare Curtains.
- Attach Drapery Hooks.
- Prepare Panels.
- Attach Magnetic Strips.
Also Know, what is the proper placement of curtain rods? The ideal position for the curtain rod is 6 inches to the left/right of the window trim. You may need to make adjustments based on how much linear space is needed for the curtain fabric to hang easily and look “full”. The finials, or decorative ends of poles may extend past the 6 inches.
Similarly one may ask, how do you install twist and fit curtain rods?
Twist-and-fit curtain rods save installation time, too.
- Measure the distance of the window opening, from one side of the interior to the other side, with a tape measure.
- Slide the rubber ring onto the thin portion of the twist-and-fit curtain rod so that it is about two inches away from the thicker portion.
Should curtains touch the floor?
The fabric should just touch the floor or hover half an inch above. This is also a great approach for café curtains (short panels that cover only the lower portion of a window and hit the sill), which work well in spots like the kitchen and bathroom, where long drapes aren’t practical.
11 Related Question Answers Found
What size curtain rod do I need?
Steps Choose a curtain rod with a diameter of at least 1 inch (2.5 cm). Thin curtain rods tend to look cheap and can bow under the weight of your drapes if they are heavy. Measure 3–6 inches (7.6–15.2 cm) beyond the window frame for rod length. Select a rod with support brackets at least every 50 inches (130 cm).
How many curtain rod brackets do I need?
Count how many brackets are included with the curtain rod. As a general rule, there should be at least one bracket for each outside corner of the window, and one bracket in the center. Add more brackets if the expanse between the middle and outer brackets is more than three feet.
What are standard curtain sizes?
When measuring for curtains, keep in mind that curtains usually come in only a few different lengths: 63 inches, 84 inches, 95 inches, 108 inches, and 120 inches. Tier curtains, which are shorter and generally don’t cover an entire window, are usually either 24 inches or 36 inches long.
How do you hang a curtain rod without a drill?
Take one of your 3M Command hooks, take off the paper backing on the adhesive strips, and line the hook up on the wall using the pencil mark for guidance. Press it on the surface well, holding for at least 30 seconds, then let it be for at least a half hour. Repeat the same for the other side. Don’t be in a rush.
Do curtain rods need to be hang on studs?
If there IS NOT a stud, you will use a drywall anchor and a screw. The anchors are the white pieces in the below photo: Knowing which to use is very important — without a drywall anchor, a screw alone will not hold the weight of the curtain and rod. If you do not have a stud finder, you can use a hammer and a nail.
How do extendable curtain rods work?
It is a telescopic pole ( i.e two sections of pole with slightly different diameters, allowing the narrower of the two to slide snugly inside the wider one), which slides in and out, making it adjustable in length to any given measurement within the maximum and minimum sizes specified.
Can tension rods hold blackout curtains?
Tension rods work well when you need to hang a curtain at a window that won’t accommodate installing a standard rod. However, you can also use them to hang sheers inside the window frame underneath curtains. You can hang just about any type of curtain on a tension rod.
What is a double curtain rod?
Double Curtain Rod Sets Add Convenience and Style A double curtain rod allows you to hang two sets of curtains and work them independently of each other. You have to move one to move the other, which defeats the purpose of having a curtain lining.
Which side of blackout lining faces the window?
The right side of the lining faces out the window.
Can you make normal curtains blackout?
So if you have existing curtains or if you’re making new curtains, you can simply add some blackout lining to the back of your curtains. Easy as that. I went to Joann Fabric and found some blackout lining for $6.99/yard but it was half off. This blackout fabric has 2 sides to it.
How much are blackout curtains?
Typical costs: Blackout curtains cost $13-$2,500 per single panel. Costs vary by quality of construction, size, materials, and brand name. Blackout curtain panels come in a range of standard sizes, up to 84 inches long and 30 or more inches wide.