How to Adjust the Tension on a Viking Sewing Machine
- Properly thread the sewing machine to ensure that the thread is threaded between the thread tension disks.
- Fold a piece of scrap fabric in half, using the same fabric you are using in the project.
- Examine the top and bottom stitches.
- Locate the thread tension dial on the sewing machine.
Moreover, why is my needle hitting the needle plate?
There could several reasons why you needle is hitting the needle plate. Make sure that the flat spot of the needle faces the back of the machine. 2. The needle clamp screw could be loose.
Beside above, how do you adjust the tension on a Viking sewing machine? How to Adjust the Tension on a Viking Sewing Machine
- Properly thread the sewing machine to ensure that the thread is threaded between the thread tension disks.
- Fold a piece of scrap fabric in half, using the same fabric you are using in the project.
- Examine the top and bottom stitches.
- Locate the thread tension dial on the sewing machine.
Similarly, how do you adjust bobbin tension?
To loosen the tension, turn to the left (counter-clockwise). To tighten the tension, turn to the right (clockwise). If you think of the screw like a face of a clock, you should be turning the screw no more than 10-15 minutes. Make a single adjustment at a time, place the bobbin back into the case and stitch.
What number should the tension be on a sewing machine?
Adjust your top tension if it’s too loose. To increase your top tension if it’s too loose, turn your knob so that the numbers are increasing. Try ½ to 1 number lower, then test the stitches on a piece of scrap fabric. Continue until it looks even on both sides and you can no longer see the bottom thread on the top.
9 Related Question Answers Found
Why does my sewing machine not stitch?
Machine is skipping stitches First, check that your needle is installed correctly, not bent or otherwise damaged, and that you’re using the right type of needle for your project. If the top thread is not reaching the bobbin, the threads will not lock properly, resulting in a skipped stitch.
Why is the stitching loose underneath?
A: Looping on the underside, or back of the fabric, means the top tension is too loose compared to the bobbin tension, so the bobbin thread is pulling too much top thread underneath. By tightening the top tension, the loops will stop, but the added tension may cause breakage, especially with sensitive threads.
Why is my thread looping underneath?
Thread looping when sewing. The proper tension on your machine will provide you with a strong seam on the material you are sewing. – While holding the bobbin in place with your finger, pass the thread through the slit in the needle plate. Loops will appear on the bottom of the fabric if the upper tension is too loose.
What causes thread to bunch up when sewing?
Bobbin Thread Tangling You will notice this when sewing. The bobbin keeps pulling and jamming collecting a lot of thread beneath your fabric. There are several culprits for this ranging from a dull needle, improper threading or tension. The tension in both your upper and bobbin threads need to be even.
What tension should I use for cotton?
Cotton requires a moderate tension setting, usually between three and four. Always start adjusting your tension settings with your upper tension.
What tension should I use for thick fabric?
You will usually be alright with a 4 or 5 on medium to medium-heavy fabrics like linen and twill weaves such as drill and denim. Thick upholstery fabrics may require a higher tension setting and a longer stitch, and lighter fabrics like cotton or even sheers will require a lower tension setting.
Why is my top thread loose?
The top thread loose could be caused by several reasons. 1. Incorrect thread tension. – Adjust the upper thread tension.
What is wrong with the tension on my sewing machine?
When the bobbin thread shows on the right side, the needle tension is too tight or the bobbin thread, too loose, as shown at left in the illustration below. When the needle thread shows on the wrong side, the needle tension is too loose or the bobbin thread, too tight, as shown at right in the illustration below.
Why is my sewing machine gathering fabric?
There is too much tension in the seam thread thus causing light, thin material to pucker. The main cause for this problem is that the sewing machine thread tension is set too high. As a rule, the thread tensions of the needle and bobbin threads must be set as low as possible.