Electrical Outlet Receptacles
Outlet receptacles for general use can be no closer than 20 feet from a pool or in-ground spa if they are not GFCI-protected, and no closer than 6 feet away if they are GFCI protected.
Correspondingly, how far does a pool need to be from power lines?
Power lines should be at least 25 feet away from the pool in all directions. Allow a minimum clearance in any direction of at least 18 feet between overhead power lines and a diving board, deck, platform, slide or observation area. Pools should never be constructed or placed over underground electric cables.
Furthermore, how do you wire an above ground pool? Plug in the pool pump and cover it with a weatherproof cover. With the main service off to the house, wire in GFCI circuit breakers to the electrical panel. Connect an 8-gauge wire to the metal posts of the pool, the pump, and the metal plate on the skimmer and then wire that to the pump to bond the entire pool.
Consequently, does a pool pump need to be on a dedicated circuit?
You want a thicker extension cord, because a pool pump requires a good amount of electricity to run. Also, because the pump uses a lot of power, the outlet that you plug the extension cord into should be on what is called a “dedicated circuit”.
Can I build a pool under power lines?
If you are thinking about installing a swimming pool, do not build it under electrical lines. Pools should only be built in areas at least 25 feet away from the power line in each direction, with at least 17 feet between overhead lines and diving boards, decks or slides.
10 Related Question Answers Found
Do you need a GFCI for a pool pump?
According to 680.22(B), all 15- or 20-ampere, 125-volt or 240-volt, single-phase outlets supplying pool pump motors are required to be provided with ground-fault circuit-interrupter protection for personnel. GFCI protection for pool pump motors is required whether supplied by receptacle or direct connection.
How much does it cost to move power lines underground?
Above ground lines cost around $10 per foot and underground lines cost in the range of $20 to $40 per foot. In highly urbanized areas the cost of underground transmission can be 10–14 times as expensive as overhead.
Are swimming pools grounded?
Grounding a Swimming Pool Grounding refers to protecting people in the pool from a potential fault in the electrical system (in the main electrical panel or pool sub-panel). A fault in the electrical system refers to a higher than normal flow of electrical current.
What wire do I use for pool pump?
Check your pool pump owners manual for the correct size. Wire sizes generally run 14 AWG for motors up to 1 HP and from 14 AWG to 10AWG for larger motors depending on HP and Voltage.
Are pool lights required?
Light Pools Evenly Every part of a pool needs to be well lit for good safety. It’s not sufficient to put some underwater lights in the deeper end of a pool and ignore the shallower end or to put only a couple of lights above the pool and leave large areas of the pool and surrounding deck in the shadows.
Can I use an extension cord for my above ground pool?
It’s highly recommended never to use an extension cord to power a pump of an above ground swimming pool. A pool pump requires a great deal of power and that you can’t provide with a normal extension cord. You’d need one with a #12-gauge wire or a #10-gauge wire.
How many amps does a 1 HP pool pump draw?
Since it’s an aboveground pool pump it’s an uprated model and probably draws in the neighborhood of 10 to 12 amps at 120 volts. Depending on your plumbing it may draw less.
How much does it cost to run electric to a pool?
General Price Range In the Virginia, Maryland, and D.C. areas, a standard electrical hook-up package for an inground pool will generally cost between $3,500 and $4,500. This standard package would include: An electrical permit.
How do you hook up a pool filter and pump?
How to Connect a Filter & Pump for a Swimming Pool Place the pump and filter assembly on level ground next to the electric source. Connect the pump to the filter housing. Attach the hose from the filter’s out spout to the pool’s return port. Connect the hose from the skimmer to the filter’s pump basket. Loosen the lid on the filter pump basket.
How many amps does a 1.5 HP pool pump draw?
I needed a new pool motor and installed was a 1.5 HP motor which has a 115/230 19.2/9.6 amp maximum load. The motor is on a 20 amp/115 volt breaker which has tripped a couple of times.