- Step 1: Measure and mark where you want your curtain rod to hang.
- Step 2: Hold your hardware in place and mark the holes.
- Step 3: Use your BLACK+DECKER Lithium Drill.
- Step 4: Drill screws into place.
- Step 5: Repeat steps 1-4 for remaining hardware.
Just so, do I need a drill to hang a curtain rod?
Rather than use a drill, you could get a large nail and hammer it in part way to make the screw holes you need. After pulling the nail back out, then you will just need to use a screw driver to mount the curtain rod brackets. Either way you will need to buy a drill bit, (or a set).
Subsequently, question is, where should curtain rod brackets be placed? Generally, hanging curtain brackets on the wall above and outside the window molding looks best, since it allows fabric to fall gracefully. If you have detailed window frames you don’t want to cover, an inside mount (hanging curtains within the frame, as you would with a tension rod) can work.
Beside above, how do you hang a curtain rod on the side?
Stationary rod lengths, whether standard or decorative, should equal one-third of the window glass width. Install them anywhere from two inches above the top of the window frame to two inches below the bottom of the ceiling molding. Hanging them at the higher end of the range makes the ceiling appear higher.
Can I hang curtains without drilling holes?
Fortunately, there are a few easy ways to hang curtains without having to drill holes in your walls. You can use adhesive hooks or a tension rod to hang up curtains without a drill.
10 Related Question Answers Found
What kind of drill Do I need to hang curtains?
Step 1: Measure and mark where you want your curtain rod to hang. Step 2: Hold your hardware in place and mark the holes. Step 3: Use your BLACK+DECKER Lithium Drill. Step 4: Drill screws into place. Step 5: Repeat steps 1-4 for remaining hardware.
How do you hang a curtain rod without a drill?
Take one of your 3M Command hooks, take off the paper backing on the adhesive strips, and line the hook up on the wall using the pencil mark for guidance. Press it on the surface well, holding for at least 30 seconds, then let it be for at least a half hour. Repeat the same for the other side. Don’t be in a rush.
What size curtain rod do I need?
Steps Choose a curtain rod with a diameter of at least 1 inch (2.5 cm). Thin curtain rods tend to look cheap and can bow under the weight of your drapes if they are heavy. Measure 3–6 inches (7.6–15.2 cm) beyond the window frame for rod length. Select a rod with support brackets at least every 50 inches (130 cm).
How many curtain rod brackets do I need?
Count how many brackets are included with the curtain rod. As a general rule, there should be at least one bracket for each outside corner of the window, and one bracket in the center. Add more brackets if the expanse between the middle and outer brackets is more than three feet.
How do you hang a curtain rod from the ceiling?
How to Hang a Curtain Rod from the Ceiling Measure and Mark. Use a pencil to mark where each ceiling-mount curtain rod bracket will go. Install Anchors. Use the power drill to install drywall anchors. Hang Curtains. Slide your curtains onto the curtain rod and insert the rod into the mounting brackets.
Can you hang curtain rods with Command Strips?
Curtains are a great way to add charm to any home. They can be merely decorative, or they can serve to block out the light. Many landlords don’t allow renters to drill holes into walls, which is necessary for installing curtain rod hooks. Fortunately, it is still possible to install curtain rods with Command hooks.
Do curtain rods need to be hang on studs?
Wall studs are usually placed at 16 or 24 inches on-center. If no wall studs are available, install wall anchors in the drywall. Screw the curtain rod brackets into the wall anchors.
Do I need wall anchors for curtain rods?
Installing a Curtain Rod in Drywall If there isn’t a stud, you’ll need to use a drywall anchor and a screw to reinforce your curtain rod brackets. Without a drywall anchor, a screw won’t be able to hold the weight of your curtain rod.
Can I use nails to hang curtain rods?
Re: Using nails instead of screws on curtain rods for lightweight curtains/valances. Yes they would, not as well though as screws. As long as the nails hit in to the wood stud on either side of the wood header in to the stud. Generally the studs are 1/2″ back from the surface of the drywall or 5/8″ if a fire rated wall
How do you hang curtains for a rental?
To hang and style curtains in a rental property, you can use 3M hardware stickers, a tension rod, or use zip ties to attach to already installed blinds. Alternatively, if you have painted brick, drill holes then reseal and paint before you move out.